Electronics Repair in Connecticut
One local bench for the electronics other shops turn away — TVs, monitors, drones, e-readers, headphones, speakers, and more. Tech Genius in Connecticut —…
One local bench for the electronics other shops turn away — TVs, monitors, drones, e-readers, headphones, speakers, and more. Not every broken gadget is a phone, a computer, or a game console — and most of those "other" devices get a shrug at the big-box counter. We are the local electronics-repair bench that actually opens them up. The work falls into a few honest categories. Anything that will not power on is usually a power problem we can trace: a failed power adapter, a swollen or dead lithium cell, a blown fuse, or a bad capacitor on the internal power board — cheaper to fix than the whole device. Anything with a broken charge or headphone jack, a loose HDMI or USB port, or a snapped-off connector is a soldering job, not a write-off. Intermittent faults, no sound, no picture, or a device that reboots itself often trace to cold solder joints, corrosion from a spill, or a failing capacitor, and we diagnose under a microscope before quoting. We handle flat-panel TVs and monitors (no picture, backlight or lines faults, cracked-panel assessments), Bluetooth headphones and speakers, e-readers and tablets, drones and RC gear, dash cams, small audio and studio gear, and the odd vintage electronics piece — where a part still exists to source. We are straight about the two limits: a cracked TV or monitor panel is usually not economical versus a new screen, and a device whose main chip has failed with no replacement part available is a no-fix — and we tell you that before you spend anything, not after. Tech Genius handles electronics repair for customers across Manchester, CT and nearby towns, typically while you wait.
Models we handle
How a repair works
Walk in during opening hours — no appointment, no booking form.
We find the actual fault and tell you the price before any work starts.
Many are done while you wait; we say up front if a part needs ordering.
Get in touch
Prefer we call you?
Leave a name and a number and we will ring you straight back during opening hours.
Visiting the store
Two Connecticut shops
1131 Tolland Turnpike
Manchester, CT 06042
Mon–Sat 11 AM–7 PM · Sunday closed
220 Route 12, STE 8A
Groton, CT 06340
Phone and opening hours confirming shortly.
Service area
Towns we cover
Common questions
Before you come in
My device is not a phone or computer — do you still fix it?
Usually yes, and that is exactly the gap we fill. Big-box counters send most non-phone, non-laptop electronics straight to the trash, but a huge share of them fail on the power supply, a bad capacitor, or a broken port — all bench-level repairs. Bring it in and we will tell you honestly whether it is a quick fix or genuinely not worth saving before you spend anything.
My TV or monitor turns on but there is no picture — is the panel dead?
Not always. A black screen with sound, or a screen that flickers then goes dark, is often a failed backlight, a bad power board, or blown capacitors — all repairable and far cheaper than a new set. A physically cracked or internally shattered LCD/OLED panel is the one case that usually is not economical, because the replacement panel costs about as much as a new TV. We open it and tell you which it is.
Can you fix a broken charging or headphone port on a speaker or headphones?
Yes — that is one of our most common jobs. A charge port, headphone jack, USB-C, or HDMI connector that wobbles, cuts out, or snapped off is a soldering repair: we desolder the damaged connector, repair any lifted pads underneath, and fit a new one. The device itself is almost never the problem.
My gadget got wet or spilled on — is it worth bringing in?
Bring it in sooner rather than later. Liquid leaves corrosion that keeps eating the board even after everything feels dry, so a device that still works today can quit next week. We clean the board, neutralize the corrosion, and replace anything already damaged — the earlier we get it, the more likely we stop the decay before it spreads.
Do you have an actual electronics technician, or is this just a parts-swap counter?
A real one, at a real bench. The difference matters: a swap counter can only replace a whole module and, when the fault is not a stocked module, hands the device back as a no-fix. A bench technician works a level deeper — reading the board with a multimeter and thermal camera, tracing a dead rail back to one blown fuse, capacitor, or MOSFET, and repairing lifted pads or a cracked trace under a microscope. That component-level and micro-soldering work is what saves the devices a swap counter writes off, and it is exactly the diagnosis we do before we quote you anything.
Do you repair drones and RC gear?
Often, yes — most drone and RC faults are the same bench-level jobs we do on other electronics. The common ones after a crash are a snapped or bent arm, cracked propellers, a wobbly or jammed camera gimbal, and damage to the flight-control or ESC board where a broken solder joint or lifted pad stops a motor. On the electrical side we see puffed or dead LiPo flight batteries and worn USB-C charge ports on the controller or the aircraft. Two honest limits: a swollen LiPo should be brought in promptly and handled carefully because a damaged lithium-polymer cell is a fire risk, and some newer drones are heavily sealed with proprietary, hard-to-source parts, so we check part availability before promising a fix. Bring it in and we will tell you whether it is repairable before you spend anything.
Do you charge just to look at it, and how long does an electronics repair take?
We diagnose first and tell you the fault and the cost before any work starts, so you decide with real numbers rather than a guess over the phone — an odd device often has to come to the bench to know what is really wrong. Turnaround depends on the part: a repair that uses common components we keep on hand — capacitors, fuses, USB-C and HDMI connectors, standard lithium cells — is frequently done the same or next day, while a fault that needs an uncommon connector, a specific board component, or a panel sourced for an older or niche device can add a few days. If a part has to be ordered we tell you the realistic wait up front instead of holding your device open-endedly.